ZX-T

Slimme contactmeetsensor

ZX-T is ideaal voor toepassingen waar het detectieobject olieafzettingen of andere microstructuren kan bevatten. In die gevallen is contactmeting de betrouwbaarste manier.

Modulair platformconcept voor verschillende detectietechnologieën
Typen die lucht innemen voor geautomatiseerde controle
Meerpuntsmeting met maximaal 8 sensoren
Drukkrachtalarm ter voorkoming van storingen
Sterke kogellagerstructuur staat borg voor een lange levensduur

Alle modellen vergelijken CAD-bibliotheek

Specificaties & bestelinfo

Ordering information

Sensors

Sensor heads

Size	Type	Sensing distance	Resolution (See note.)	Order code
6 dia.	Short type	1 mm	0.1 µm	ZX-TDS01T
	Standard type	4 mm		ZX-TDS04T
	Low-load type	4 mm		ZX-TDS04T-L
8 dia.	Standard type	10 mm	0.4 µm	ZX-TDS10T
	Ultra-low-load type			ZX-TDS10T-L
	Air lift type			ZX-TDS10T-V
	Air lift/air push type			ZX-TDS10T-VL

Note: The resolution refers to the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected.

Amplifier units

Power supply	Output type	Order code
DC	NPN	ZX-TDA11
DC	PNP	ZX-TDA41

Accessories (order separately)

Calculating unit

	Order code
Calculating unit	ZX-CAL2

ZX-series communications interface unit

Name	Order code
ZX-series communications interface unit	ZX-SF11

SmartMonitor sensor setup tool for Personal Computer connection

Name

Order code

ZX-series communications interface unit

ZX-SF11

ZX-series communications interface unit

+ setup software (CD-ROM)

ZX-SFW11EV31 , 2

ZX-series sensor setup and logging software (CD-ROM)

ZX-SW11EV31

Cables with connectors on both ends (for extension)*

Cable length	Order code
1 m	ZX-XC1A
4 m	ZX-XC4A
8 m	ZX-XC8A

* Robot cable models are also available. The model numbers are ZX-XC_R.

Preamplifier mounting brackets

Remarks	Order code
Attached to each sensor head	ZX-XBT1
For DIN track mounting	ZX-XBT2

Actuators

Type (material)	Screw section	Appearance	Application	Applicable sensor (see note.)	Order code
Type (material)	Screw section	Appearance	Application	ZX-TDS_T
Ball type (steel)	Female screw M2.5x0.45		Measuring ordinary flat surfaces (standard actuator supplied with the ZX-TDS series)		D5SN-TB1
Ball type (carbide steel)	Female screw M2.5x0.45		Measurements where abrasion resistance is critical Measured objects: Carbide (HR90) or lower.		D5SN-TB2
Ball type (ruby)	Female screw M2.5x0.45		Measurements where abrasion resistance is critical Measured objects: Carbide (HR90) or higher.		D5SN-TB3
Needle type (carbide steel)	Male screw M2.5x0.45		Measuring the bottom of grooves and holes		D5SN-TN1
Flat (carbide steel)	Male screw M2.5x0.45		Measuring spherical objects		D5SN-TF1
Conversion adapter (stainless steel)	Through-hole female screw M2.5x0.45		Mounting D5SN-TN1/-TF1 or commercially available actuators on ZX-TDS-series sensors		D5SN-TA

Note: Replacement possible Conversion adapter required

Specifications

Amplifier units

Item	ZX-TDA11	ZX-TDA41
Measurement period	1 ms
Possible average count settings3	1, 16, 32, 64, 128, 256, 512, or 1,024
Linear output4	Current output: 4 to 20 mA/F.S., max. load resistance: 300 Ω Voltage output: ±4 V (±5 V, 1 to 5 V5), output impedance: 100 Ω
Judgement outputs (3 outputs: HIGH/PASS/LOW)	NPN open-collector outputs, 30 VDC, 30 mA max. Residual voltage: 1.2 V max.	PNP open-collector outputs, 30 VDC, 30 mA max. Residual voltage: 2 V max.
Zero reset input, timing input, reset input, judgement output hold input	ON: Short-circuited with 0-V terminal or 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)	ON: Supply voltage short-circuited or supply voltage of 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)
Function	Measurement value display present value/set value/output value display Display reverse ECO mode number of display digit changes Sample hold peak hold bottom hold, peak-to-peak hold Self-peak hold self-bottom hold zero reset Initial reset direct threshold value setting position teaching Hysteresis width setting timing inputs reset input Judgement output hold input monitor focus (A-B) calculations6 (A+B) calculations (see note 4.) sensor disconnection detection Zero reset memory function lock non-measurement setting Clamp value setting scale inversion zero reset indicator Span adjustment warming-up display pressing force alarm
Indicators	Judgement indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red), 7-segment sub-digital display (yellow), power ON (green), zero reset (green), enable (green)
Power supply voltage	12 to 24 VDC±10%, ripple (p-p): 10% max.
Current consumption	140 mA max. (with sensor connected), for 24-VDC power supply voltage: 140 mA max. (with sensor connected)
Ambient temperature	Operating and storage: 0 to 50°C (with no icing or condensation)
Temperature characteristic	0.03% F.S./°C
Connection method	Prewired (standard cable length: 2 m)
Weight (packed state)	Approx. 350 g
Materials	Case: PBT (polybutylene terephthalate), cover: Polycarbonate

Sensor heads

Item		ZX-TDS01T	ZX-TDS04T	ZX-TDS04T-L
Measurement range		1 mm	4 mm
Maximum actuator travel distance		Approx. 1.5 mm	Approx. 5 mm
Resolution7		0.1 µm
Linearity8		±0.3% F.S.
Operating force 9		Approx. 0.7 N		Approx. 0.25 N
Degree of protection (sensor head)		IEC60529, IP67		IEC60529, IP54
Mechanical durability		10,000,000 operations min.
Ambient temperature		Operating: 0 to 50°C, storage: - 15 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no icing or condensation)
Temperature characteristic10	Sensor head	0.03% F.S./°C
Temperature characteristic10	Preamplifier	0.01% F.S./°C
Weight (packed state)		Approx. 100 g
Materials	Sensor head	Stainless steel
Materials	Preamplifier	Polycarbonate
Accessories		Instruction manual, preamplifier mounting brackets (ZX-XBT1)

1. When using the ZX-TDA11/41 with the SmartMonitor, either the ZX-SFW11EV3 or the
ZX-SW11EV3 SmartMonitor must be used. Earlier versions cannot be used.

2. The ZX-SFW11EV3 SmartMonitor can be used only to set functions and monitor waveforms.

3. The response speed of the linear output is calculated as the measurement period x (average count setting + 1).
The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1).

4. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.

5. Setting is possible via the monitor focus function.

6. A calculating unit (ZX-CAL2) is required.

7. The resolution is given as the minimum value that can be read when a ZX-TDA_1 amplifier unit is connected. This value is taken 15 minutes after turning ON the power with the average number of operations set to 256.

8. The linearity is given as the error in an ideal straight line displacement output.

9. These figures are representative values that apply for the measurement mid-point, and are for when the provided actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the weight of the actuator itself.

10. These figures are representative values that apply for the mid-point of the measurement range.

1. When using the ZX-TDA11/41 with the SmartMonitor, either the ZX-SFW11EV3 or the
ZX-SW11EV3 SmartMonitor must be used. Earlier versions cannot be used.

2. The ZX-SFW11EV3 SmartMonitor can be used only to set functions and monitor waveforms.

4. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.

5. Setting is possible via the monitor focus function.

6. A calculating unit (ZX-CAL2) is required.

8. The linearity is given as the error in an ideal straight line displacement output.

10. These figures are representative values that apply for the mid-point of the measurement range.

Hoe kunnen we u helpen?

Als u een vraag hebt of een offerte wilt aanvragen, kunt u contact met ons opnemen of een verzoek indienen.

+32 (0) 2 466 24 80

Offerte aanvragen

Offerte voor ZX-T

Met dit formulier kunt u een prijsaanvraag doen voor de producten van uw keuze. Vul alstublieft alle velden in die gemarkeerd zijn met *. Uw persoonlijke gegevens behandelen wij uiteraard volstrekt vertrouwelijk.

Persoonlijke gegevens

Product ZX-T

Naam

Text error notification

Achternaam

Text error notification

E-mail

Email error notification

Telefoon

Text error notification

Bedrijf

Text error notification

Land

Country error notification

Offerte details

Koopt u bij Omron of bij een distributeur/partner?

Select notification error

Titel/Positie

Select notification error

Vragen of opmerkingen

Text area error notification

Ik ga akkoord met OMRON Privacy Policy

Checkbox error notification

Meld u aan voor de nieuwsbrief

Checkbox error notification

Dank u wel voor uw aanvraag. Wij zenden u de gewenste informatie zo snel als mogelijk.

Wij ondervinden technische problemen. Uw formulierinzending is niet gelukt. Onze verontschuldigingen hiervoor, probeer het later nog een keer. Details: [details]

Download

Offerte aanvragen